- Mon - Sat : 9:00 - 17:00
- + 91-9924300407
- saffromellow@yahoo.com
Description
Two-component air-drying intermediate/primer surfacer coat.
Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats.
| COLOUR : | Grey, White |
|---|---|
| FINISH : | Egg Shell to Matt |
| SOLIDS BY VOLUME : | 40 ± 3% |
| SPREADING RATE : | 13.3 sq.mt / ltr at recommended DFT of 30 µ |
| FLASH POINT : | Base : 23°C Hardener : 23°C |
| DRYING CHARACTERISTICS (At 30°C & 65% Relative Humidity) : | SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days |
| SHELF LIFE : | BASE : 6 months HARDENER : 6 months |
This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting.
| MIXING RATIO : | Base: Hardener ( As per our recommendation) |
|---|---|
| APPLICATION : | By Brush/ By Conventional Spray / By Airless Spray |
| THINNER : | Type 290 |
| POT LIFE : | 4 hours min at 30° C |
| RECOMMENDED DFT : | 30 -35 µ. |
| OVERCOATING INTERVAL : | MIN : 8 hours MAX : 24 hours |
| COMPATIBILITY : | Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers. |
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix thoroughly to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir thoroughly for few minutes. Allow the mixture to stand still (maturation) for about 10 minutes to initiate the reaction. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensure the uniform application. Use quality brushes for paint application.
| Thinner : | Type 290 |
|---|---|
| Addition : | 5-15% |
| Nozzle Orifice : | 1.2-1.4mm |
| Nozzle Pressure : | 40-70 p.s.i |
| Thinner : | Type 290 |
|---|---|
| Addition : | Max 5%, if required. |
| Nozzle Orifice : | 0.28-0.37 mm |
| Nozzle Pressure : | 1400-1800 p.s.i |
1. Do not apply paint when temperature falls below 10°C or rises above 50°C and when Relative Humidity is above 85%. Do not apply during rain, fog or mist. Surface temperature must always be minimum of 3°C above Dew point.
2. Brushes and spray equipment should be cleaned with SAFFRO's recommended thinner otherwise equipment is liable to be damaged.
3. DFT variation can be obtained by change in application method / thinning ratio.
4. Shelf life indicated is minimum for this Product in sealed conditions and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition.
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapours as well as contact between the wet paint and exposed skin or eyes.
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchantability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchased price. Labour or cost of labour and other consequential damages are hereby excluded.
